Series 2 - 5 aluminum straight sections

• Series:   24, H24, 25, 26, 27, 34, 35, 36, 37, 46, H46, 56, 47, H47, 57
  
• Material:  aluminum
  
• Types: ladder, solid bottom, ventilated trough, and non-ventilated trough
• Widths: 6, 9, 12, 18, 24, 30 and 36 inches
• Lengths: available rom 10 ft. to 40 ft. (depending on series selected)

Series 2 - 5 steel straight sections

• Series:  248, 258, 268, 346, 356, 366, 378, 444, 454, 464, 476, and 574
  
• Types: ladder, solid bottom, ventilated trough, and non-ventilated trough
  
• Materials:  pre-galvanized steel, hot dip galvanized steel, and stainless steel type 304 and 316L
  
• Widths: 6, 9, 12, 18, 24, 30 and 36 inches
• Lengths: Available from 10 ft. to 24 ft. (depending on series selected)

Overview

• Material: aluminum, hot dip galvanized steel, pre-galvanized steel, 304 stainless steel, 316 stainless steel
• Side rail heights: 4" (101mm), 5" (127mm), 6" (152mm), 7"(178mm)
• Width: 6" (152mm), 9" (228mm), 12" (305mm), 18" (457mm), 24" (609mm), 30" (762mm), 36" (914mm)
• Angles: 30°, 45°, 60°, 90°
• Radius: 12" (305mm), 24" (609mm), 36" (914mm), 48" (1219mm)

Fittings

• Horizontal bends
• Horizontal tees
• Horizontal crosses
• Vertical inside / outside bends
• Vertical tees
• Vertical tees, up
• Horizontal wyes, right and left
• Cable supports 
• Left and right reducers
• Straight reducers

• Types:  solid, ventilated, and peaked
• Options: flanged, non-flanged
  • Diamond tread plate covers available in aluminum.
• Available for tray widths: 6, 9, 12, 18, 24, 30 and 36 inches
• Lengths:  12, 10, 6 and 5 ft. options (HDGAF available in 6 and 5 ft. only)

• Standard cover clamp, indoor only
• Combination cover and hold down clamp, indoor only
• Raised cover clamp, indoor service for flanged covers only
• Heavy duty cover clamp, outdoor service
• Aluminum cover support bracket - designed to eliminate cover sag concerns due to environmental loads (snow, ice, debris).  Available for widths 12” and larger.

Aluminum accessories

• Wedge lock splice plates
  • Standard four-hole pattern
  • One pair including hardware provided with each section (Expansion splice quantity subtracted)
  • For field installation drill 13/32" hole
    
  • Models: 9A-1004 , 9A-1005, 9A-1006, 9A-1007
• Expansion splice plates
  • Allows for one inch expansion or contraction of cable tray or where expansion joints occur in the supporting structure
  • Bonding jumpers are required on each side rail (sold separately)
  • Models: 9A-1014, 9A-1015, 9A-1016, 9A-1017 
• Mid-span splice plates
  • Standard for series H64A, H47A and 57A straight sections
  • Available on ladder bottoms only.; 09 and 12" rung spacing
    
  • Models: 9A-6006 for series H46A, and 9A-6007 for series H47A and 57A
• Universal splice plates
  • Models: 9A-1004-1/2, 9A-1005-1/2, 9A-1006-1/2, 9A-1007-1/2 7 (178)
• Step down splice plates    
  • Used for connecting cable tray sections having side rails of different heights
  •  Models: 
    • 9A-1045 for 5" to 4" (127mm to 101mm) step down
    • 9A-1046 for 6" to 4" (152mm to 101mm) step down
    • 9A-1060 for 6" to 5" (152mm to 127mm) step down
    • 9A-1047 for 7" to 4" (178mm to 101mm) step down
    • 9A-1061 for 7" to 5" (178mm to 127mm) step down
    • 9A-1062 for 7" to 6" (178mm to 152mm) step down
• Vertical adjustable splice plates 
  • Used for changes in elevation that do not conform to standard vertical fittings
  • Bonding jumpers not required
  • Models: 9A-1024, 9A-1025, 9A-1026, 9A-1027
• Horizontal adjustable splice plates
  • Used to adjust cable tray run for changes in direction in a horizontal plane that do not conform to standard horizontal fittings
  • Bonding jumpers not required
    
  • Models: 9A-103(X), 9A-103(X)-12, 9A-103(X)-36 (For X, insert side rail height)

Steel accessories

• Splice plates 
  • Standard 8-hole pattern for all steel splice plates.
  • Furnished in pairs with hardware.
  • One pair including hardware provided with straight section (Expansion splice quantity subtracted)
  • Models: 9ZN-8004, 9ZN-8005, 9ZN-8006,  9ZN-8007, 9G-8004, 9G-8005, 9G-8006,  9G-8007
    
• Expansion splice plates
  • Allows for one inch expansion or contraction of the cable tray, or where expansion joints occur in the support structure
  • Furnished in pairs with hardware
  • Bonding Jumpers are required on each siderail
  • Models: 9ZN-8014, 9ZN-8015, 9ZN-8016, 9ZN-8017, 9G-8014, 9G-8015, 9G-8016, 9G-8017
    
• Universal splice plates
  • Used to splice to existing cable tray systems
  • Models: 9ZN-8004-1/2, 9ZN-8005-1/2, 9ZN-8006-1/2, 9ZN-8007-1/2, 9G-8004-1/2, 9G-8005-1/2, 9G-8006-1/2, 9G-8007-1/2
    
• Step down splice plates
  • Used for connecting cable tray sections having side rails of different heights
  • Models: (*) insert ZN or G
    • 9(*)-8045 for 5" to 4" (127mm to 101mm) step down
    • 9(*)-8046 for 6" to 4" (152mm to 101mm) step down
    • 9(*)-8060 for 6" to 5" (152mm to 127mm) step down
    • 9(*)-8047 for 7" to 4" (178mm to 101mm) step down
    • 9(*)-8061 for 7" to 5" (178mm to 127mm) step down
    • 9(*)-8062 for 7" to 6" (178mm to 152mm) step down
• Vertical adjustable splice plates
  • Used for changes in elevation that do not conform to standard vertical fittings
  • Bonding jumpers not required
  • Models: 9ZN-8024,  9ZN-8025, 9ZN-8026, 9ZN-8027, 9G-8024,  9G-8025, 9G-8026, 9G-8027
    
• Branch pivot connectors
  • Branch from existing cable tray runs at any point; pivot to any required angle
  • UL Classified for grounding (bonding jumpers not required)
  • Models: 9ZN-8244, 9ZN-8245, 9ZN-8246, 9ZN-8247, 9G-8244, 9G-8245, 9G-8246, 9G-8247
    
• Heavy duty hold down brackets
  • Recommended for support of vertical trays
  • Design load is 2000 lbs (8.89kN) per pair
  • Two bolt design; sold in pairs
  •  3/8" cable tray attachment hardware provided
  • Model: 9ZN-1241, 9G-1241
• Heavy duty hold down brackets
  • Recommended for support of vertical trays
  • Design load is 4000 lbs (17.79kN) per pair
  • Four bolt design; sold in pairs.
  • 3/8" cable tray attachment hardware provided
  • Model: 9ZN-1242, 9G-1242

• Conduit to cable tray adaptor
  • Model:  9ZN-1155-(insert conduit size
    1/2" to 4")
• Bonding jumpers
  
  • Use at each expansion splice and where the cable tray is not mechanically/electrically continuous to ground.
    • See B-Line series cable tray catalog for amperage ratings required to match the UL cross-sectional area of tray.  See tray loading chart for UL cross-sectional area.
  • Models: 
    • 99-N1 for copper wire size #1,  600 amps
    • 99-40 for cooper wire size 4/0,  1600 amps
    • 99-1620 for 250 MCM cooper wire size,  2000 amps
• Grounding clamp
  • Eaton’s B-Line series cable tray is UL® classified as to its suitability as an equipment grounding conductor
  • If a separate conductor for additional grounding capability is desired, this clamp is used for bolting the conductor at least once to each cable tray section
  • Accepts #6 AWG to 250 MCM
  • Model: 9A-2130
  • Material: tin plated aluminum
• Cable tray clamp / guide
  • No-twist design with up to four times the strength of the traditional design
  • Each side is labeled to ensure proper installation
  • Not recommended for vertical support
    
  • Models with hardware: 9ZN-1204, 9ZN-1208, 9A-1205, 9G-1205, 9SS6-1205, 9ZN-1205

• Cable tray clamp
  • Hold-down clamps for single or double cable tray runs
  • No drilling of support I-beam or channel required
  • Sold in pieces - two clamps are required per tray
  • Maximum beam flange thickness 11/8" (28.58 mm)
  • Models: 9ZN-1249HD, 9G-1249HD
• Cable tray guide
  • Expansion guide for single or double cable tray runs
  • Allows for longitudinal movement of the cable tray
  • No field drilling of support I-beam or channel
  • Guides are required on both sides of cable tray to prevent lateral movement - can be placed on either the inside or outside flange of cable tray
  • Guides are sold in pieces - two guides are required per tray
  • Maximum flange thickness 11/8" (28.58 mm)
  • Models: 9ZN-1249, 9G-1249
• Isolator pad
  • Use as a friction reducer and/or as a dissimilar metal isolator barrier
  • UV resistant HDPE
  • Temperature range: -100 to 160° F
  • Designed to use with 9(*)-1205 or 9(*)-1208 clamp/guide
  • Model: 99-PE34

Series S8 straight sections

• Material: aluminum
• Width: 12, 18, 24, 30 and 36 inches
• Length: 40, 30 and 25 feet

Series S8 fittings

• Horizontal bends
• Horizontal tees 
• Horizontal crosses
• Vertical outside bends
• Vertical inside bends
• Reducers

Series S8 accessories

• Splice plate: 9A-1008
• Expansion splice plate: 9A-1018
• Horizontal adjustable splice plate: 9A-1038
• Vertical adjustable splice plate: 9A-1028
• Hold down clamps - 9ZN-1281, 9G-1281,
  9A-1281
• Guides: S9ZN-1202, S9G-1202
• Step down splice plates:
  • 9A-1048 = 8” to 4”
  • 9A-1051 = 8” to 5”
  • 9A-1050 = 8” to 6”
  • 9A-1078 = 8” to 7”
• Offset splice plates and blind ends
• Covers: Standard aluminum cover number with S in front